Products Welcome History Products  

Venting Systems for Tankless Water Heaters

  • Z-Vent is manufactured using AL29-4C® Advanced Ferritic Stainless Steel for Use with Condensing Furnances, Boilers, Tankless Water Heaters, Pool Heaters
  • Z-Vent is Used for Gas Venting for Category II, III, IV Heating Equipment
  • Z-Vent Uses a Fair-safe Gasket connection.  No Sealant is Required.
  • Features the Highest Pressure Rating in the Industry
  • The Only Metallic Special Gas Vent You Can Cut to Length on Site
  • 1” Clearance to Combustibles

 

Z-Vent Pipe

  • Stocked in 3” and 4” Diameters and Various Lengths Up to 10’
  • Larger Diameter Available by Special Order

 

Z-Vent Condensation Drain Pipe

  • Available in 3” and 4” Diameter
  • Used to Drain Condensation on a Horizontal Run
  • Larger Diameter Available By Special Order

 

Z-Vent Top Support Storm Collar

  • Designed For Use in a Vertical Installation of Z-Vent.  Supports the Vent Run Above the Flashing
  • Also Has Built-in Storm Collar

 

Z-Vent Termination Tee

  • Horizontal Termination Tee with Screen
  • Stocked in 3” and 4”
  • Larger Diameter Available by Special Order

 

Z-Vent Adjustable Roof Flashing

  • Adjusts From 0/12 to 6/12 Pitch
  • Stocked in 3” and 4” Diameter

 

Z-Vent Vertical Drain Pipe

  • Stocked in 3” and 4” Diameter
  • Larger Diameter Available by Special Order

 

Z-Vent Condensation Drain Tube Kit

  • 3/8” I.D. High Temperature Silicone Tubing for Draining Condensation

 

Z-Vent Flat Roof/Chimney Flashing

  • Used on a Flat Roof or Chimney Application
  • Stocked in 3” and 4” Diameter
  • Larger Diameter Available by Special Order

 

Z-Vent Termination Box

  • Horizontal Box Style Termination with Screen
  • Stocked in 3” and 4” Diameter
  • Larger Diameter Available by Special Order

 

Z-Vent Sealant

  • 3 Ounce Tube of High Temperature Sealant

 

Z-Vent Vertical Drain Tee

  • Available in 3” and 4” Diameters
  • Used to Drain Condensation on a Vertical Run
  • Larger Diameter Available by Special Order

 

Z-Vent Thimble (Adjustable)

  • Designed for Horizontal Runs of Z-Vent When Passing Pipe Through a Combustible Wall
  • Adjusts from 4” to 7”

 

Z-Vent Elbows

  • Stocked in 3” and 4” Diameter in Both 45˚ and 90˚
  • Larger Diameter Available by Special Order

 

Z-Vent Fire Stop Support

  • Used as a Fire Stop and Support on a Vertical Installation When Penetrating a Floor or Ceiling

 

Z-Vent Fire Stop Spacer

  • Used on a Vertical Installation When Penetrating a Floor or Ceiling

 

Z-Vent Rain Cap

  • Vertical Rain Cap Termination
  • Cap has Built-in Storm Collar
  • Stocked in 3” and 4” Diameter
  • Available in Larger Diameter by Special Order

 

Z-Vent 4”-3” Reducer

  • Used to Reduce From 4” Z-Vent to 3” Z-Vent or a 4” Flue Collar to 3” Z-Vent Pipe
  • 3” End is Female
  • 3” – 4” Increaser Available